Wren 80 Jubilee flameout Acceleration Error
Publié : lun. sept. 27, 2021 4:31 pm
Milles excuse j'ai poster en Anglais,,,
Oh dear here we go again,,,
Voila mon problème, lenteur de démarrage elle passe une temps infini a 9.000tm,
deuxième problème, flameout " Acceleration Error" a 100.000 tm, maintenant modifier, j'ai passer le
Acc delay de 008 a 010 ( conseilleur sur youbob a 017 mais trop lent et instable )
Wait to the very end of the video for the 'Acceleration error"
This is my Wren 80 it starts slowly and hovers around the 9.000 / 10.000 rpm mark,
I start it and then when accelerating from Idle it flames out at around 100.000 rpm,
here are my settings, some were modified from new as when I bought it as it would not start !
Lien video
https://youtu.be/Kfr-ejQMNsU" onclick="window.open(this.href);return false;
Pump start point 030 ( tried 026 and up to 032 )
Pump start ramp 004, then 005 and at 006 the same
glow 6.5v ( lipo 7.4 2s 2400mah )
low batt voltage 6v
starter power fuel ramp70
rpm 100% 26.000rpm
rpm off 30.000
rpm reconnect 26.000
rpm ign kero 6.000
pump power ign kero 034
engine mini flow 30
egt end pre heat kero 200° ( was 180° )
rpm preheat kero 9.000
rpm fuel ramp kero 22.000
preheat fuel 035
ign timeout 25.5
acc delay 008
deceleration delay 006
stab 100 pump limit 752.
I have posted another video with its flame out if anyone can help me,,,
" Acceleration error"
Ecu Xicoy 10
F***** for some raison youboob have blocked the commentaries, but I did get a private message that Wrens advice was to push the acc delay from 008 to 017, i did but slow and unstable so I put it to 010, that seems ok.
I also dropped the End preheat kero from 200° to the factory setting of 180°, but no difference still staying for ages at 9.000 rpm,,donc une problème de preheat ?, et comment le modifier ?.
Oh dear here we go again,,,
Voila mon problème, lenteur de démarrage elle passe une temps infini a 9.000tm,
deuxième problème, flameout " Acceleration Error" a 100.000 tm, maintenant modifier, j'ai passer le
Acc delay de 008 a 010 ( conseilleur sur youbob a 017 mais trop lent et instable )
Wait to the very end of the video for the 'Acceleration error"
This is my Wren 80 it starts slowly and hovers around the 9.000 / 10.000 rpm mark,
I start it and then when accelerating from Idle it flames out at around 100.000 rpm,
here are my settings, some were modified from new as when I bought it as it would not start !
Lien video
https://youtu.be/Kfr-ejQMNsU" onclick="window.open(this.href);return false;
Pump start point 030 ( tried 026 and up to 032 )
Pump start ramp 004, then 005 and at 006 the same
glow 6.5v ( lipo 7.4 2s 2400mah )
low batt voltage 6v
starter power fuel ramp70
rpm 100% 26.000rpm
rpm off 30.000
rpm reconnect 26.000
rpm ign kero 6.000
pump power ign kero 034
engine mini flow 30
egt end pre heat kero 200° ( was 180° )
rpm preheat kero 9.000
rpm fuel ramp kero 22.000
preheat fuel 035
ign timeout 25.5
acc delay 008
deceleration delay 006
stab 100 pump limit 752.
I have posted another video with its flame out if anyone can help me,,,
" Acceleration error"
Ecu Xicoy 10
F***** for some raison youboob have blocked the commentaries, but I did get a private message that Wrens advice was to push the acc delay from 008 to 017, i did but slow and unstable so I put it to 010, that seems ok.
I also dropped the End preheat kero from 200° to the factory setting of 180°, but no difference still staying for ages at 9.000 rpm,,donc une problème de preheat ?, et comment le modifier ?.